Nary a problem..

I had velcro on the front portion of the stock for over 3 years - I just took it off a couple of months ago because I have a different laser, and I took the old velcro off and added new velcro in a different spot...

I also have had velcro in the ejection port area for about 4 years now.

 

I agree with ship, perpect place for pressure switch. YOu can put it on the other side too. I keep my thumb paralell to the bore anyhow, my thumb on the reloading hand has no business being in the trigger area.

My advice is go to the nearest craft and/or sewing machine place and buy the velcro in the packets. You can put the fuzzy velcro part on your rifle generiously... to receive your pressure switch with the grabby part of the velcro.

 

I bought my velcro at Wal-Mart in the sewing section.

I use it a lot actually. I put some on my MSAR near the ejection port - as ejected cases hit the polymer stock and can ding it up.

I also have a Mustang, and the plastic console by my knee is very close to my right leg. When driving, that hard plastic edge would bother my knee (I have bad knees).

So, I put velcro on the side, and got one of those seatbelt cushions you can buy (long, thin pillow basically). Got one in black, and velcroed it on the side.

Now, my leg rests against the pillow instead of the hard plastic. Yea for velcro

 

lol Shipwreck MacGuyver

So I'm guessing the contact time isn't really long enough for the temperature of the shell/gases being expelled to melt the Velcro?

 

No, it stays put. The hot cases hitting it is only for a super short period.

 

make sure you clean the surface before sticking the velcro backing on. simple light soap and water works fine as long as your hands are also clean. i bought a roll of velcro at walmart.

here's my pressure switch locations including the soft velcro on the butt stock for us skinny guys.

I put some velcro on the bottom trigger guard/handle so i don't scratch it when shooting off a bench or something solid.

velcro'd cheek pad (it was extra padding from my range bag).

even though the recoil is negligible, my boney colar bone still feels it. that thin strip of velcro does a good job.

-a|ex

 

How's that front one work for you? It seems like it'd be awkward to me.

 

How's that front one work for you? It seems like it'd be awkward to me.

No, I had mine there when I had a cheap laser before I got my Unimax. I prefer it on the front myself. Just wrap 1 finger around to activate it - but it stays out the way otherwise.

My Unimax switch was too big to go there, unfortunately

 

Thanks, guys. I'm going to try replacing the Velcro that came with my light & laser and try again. Appreciate the input!

 

Thanks, guys. I'm going to try replacing the Velcro that came with my light & laser and try again. Appreciate the input!

Yea - the walmart stuff works pretty well. give that a shot...

 

Shipwreck-The-Sequel, ShipWreck, make up your mind which one you going to use!!!! :?:


:-D

 

Shipwreck-The-Sequel, ShipWreck, make up your mind which one you going to use!!!! :?:


:-D

I did decide... I switched to this acct on Sat... (after that post above)...

:-x

I'm going to only use this act... at least until the 3rd one comes out... Shipwreck is a trilogy

:lol:

 

Shipwreck-The-Sequel, ShipWreck, make up your mind which one you going to use!!!! :?:


:-D

I did decide... I switched to this acct on Sat... (after that post above)...

:-x

I'm going to only use this act... at least until the 3rd one comes out... Shipwreck is a trilogy

:lol:

:-D OK

 

Subtitle "Will somebody move these damn rocks?"

 

Someone here on the forum hard wired two micro switches to the grip area and on the front hand guard below the barrel installed two jacks, One was for the light the other for the laser.

 

Pics or it didn't happen?

 

Someone here on the forum hard wired two micro switches to the grip area and on the front hand guard below the barrel installed two jacks, One was for the light the other for the laser.

Interesting idea...

 

Someone here on the forum hard wired two micro switches to the grip area and on the front hand guard below the barrel installed two jacks, One was for the light the other for the laser.

Here's a link to the thread (Pics are mid-way through Page 2)

http://fnforum.net/dropped-off-the-ps-for-stg-1-mods-updated-t1354-25.html

 

Someone here on the forum hard wired two micro switches to the grip area and on the front hand guard below the barrel installed two jacks, One was for the light the other for the laser.

Here's a link to the thread (Pics are mid-way through Page 2)

http://fnforum.net/dropped-off-the-ps-for-stg-1-mods-updated-t1354-25.html

That gun in that thread is just too super sweet!

 

I tried eveything looking for that post, Glad you found it, Thanks AZRobbo

 

No problem. I had just read it a few hours before I saw this thread; and like you, I hard a difficult time finding it.

Perhaps it's because the thread title doesn't mention anything about lasers, switches or mods to the stock.

Glad I could help.