FN Herstal Firearms banner
1 - 20 of 28 Posts

·
Premium Member
Joined
·
1,300 Posts
Discussion Starter · #1 ·
Changes to the SSL's are as Follows:


  • .030" Machined boss on the back side of each lever to hole the Tail off the receiver during articulation
  • Revised Depth and Bolt hole diameter on Dimpled version to make them less abrasive to the Non-Machinist handed.
  • All Varieties now available with out the PMM logo
  • Finally a price reduction from 22.50 per unit to $18.00
  • All style available in FDE & Black



Lastly If you have not tried my SSL'S over the others on the market I highly encourage you to do So, they are 2nd to non when it comes to positive safety manipulation as well as increased leverage and ergonomics for the shooter especially when mated with a PMM Modified Grip for the SCAR.
 

·
Registered
Joined
·
21 Posts
Levers came in and I installed them, very nice fit and finish very comfortable. I am right handed so I ordered a long left and a short right. The Short is actually the same size as the OEM long lever. They work extremely well. Instructions were very good. I also ordered the front and rear qd mounts.
 

·
Premium Member
Joined
·
1,300 Posts
Discussion Starter · #13 ·
Levers came in and I installed them, very nice fit and finish very comfortable. I am right handed so I ordered a long left and a short right. The Short is actually the same size as the OEM long lever. They work extremely well. Instructions were very good. I also ordered the front and rear qd mounts.

Thank you sir!
 

·
Registered
Joined
·
21 Posts
QD mounts came in as well, installed them easily, however, my sling swivels are a bit out of spec compared to the PMM mounts, because they are very loose and pull out, the swivels aren't bad, they just will only fit and work with their original mounts and not the PMMs, gonna order some swivels from you as well.
 

·
Premium Member
Joined
·
1,300 Posts
Discussion Starter · #15 ·
QD mounts came in as well, installed them easily, however, my sling swivels are a bit out of spec compared to the PMM mounts, because they are very loose and pull out, the swivels aren't bad, they just will only fit and work with their original mounts and not the PMMs, gonna order some swivels from you as well.

I saw your order and will send you the B-Hawk QD's. If those don't fit and and lock in place I will get you a replacement set of QD mounts.
~Jrod.
 

·
Registered
Joined
·
21 Posts
The ones I had aren't "heavy duty" and the depth from the shoulder of the mounting surface to the centers of the bearings are just short enough to not them seat and the diameter of the pin is smaller so there is slop. The ones you sent completely seat and fit snug. Thanks Jarod.
 

·
Premium Member
Joined
·
1,300 Posts
Discussion Starter · #17 ·
The ones I had aren't "heavy duty" and the depth from the shoulder of the mounting surface to the centers of the bearings are just short enough to not them seat and the diameter of the pin is smaller so there is slop. The ones you sent completely seat and fit snug. Thanks Jarod.
Star.ranger, Glad you like them I pride myself on my work.
~Jrod.
 

·
Premium Member
Joined
·
1,300 Posts
Discussion Starter · #20 ·
Jarod, which style is which? The pictures aren't labeled on the website so it's hard to tell. I want to order the style below, I believe this is the ERGO, but wanted to make sure:

Brett, If you Scroll down to the Bottom of the SSl page there is an Image that shows the styles and names of them .As seen here. Metal
 
1 - 20 of 28 Posts
Top