[TactiTex]

After sighting in the RMR a couple of weeks ago I found that it doesnt co witness with the irons so I broke out the depth mics and found the front site is almost .050 to the right. Just about the exact amount my co witness is off.
Can anyone recommend a sight pusher that works well with the FNX.45 Tac?

 

[wespac78]

I use the P500 sight pusher from B&J Machine. No complaints so far and it's much cheaper than the MGW Sight Pro.

 

[TactiTex]

So no problems marring the blade on the sight or anything?

 

[TactiTex]

I guess my next problem is finding one.

 

[wespac78]

So no problems marring the blade on the sight or anything?

No, just use masking tape like you always should and you don't have to worry about any marks or marring.

 

[djv38]

I have one of these: Fisher Solutions - Home - El Cajon, CA

Haven't used it on my Tac, but it works well and doesn't mar the sights (I did not put tape on the part that actually contacts the sight itself, but did use a couple of layers on the clamp portion and shimmed it with a bit of cardboard under the slide for my FNP 9)

 

[wespac78]

Typically, as a precaution, it is a good idea to put masking tape over any area where you may take the chance of marking or marring the finish. Just an added layer of protection 😀

 

[TactiTex]

Appreciate the info everyone.

 

[TactiTex]

I have one of these: Fisher Solutions - Home - El Cajon, CA

Haven't used it on my Tac, but it works well and doesn't mar the sights (I did not put tape on the part that actually contacts the sight itself, but did use a couple of layers on the clamp portion and shimmed it with a bit of cardboard under the slide for my FNP 9)

I'll give this one a shot. The P500 is nowhere to be found.

 

[TactiTex]

I have one of these: Fisher Solutions - Home - El Cajon, CA

Haven't used it on my Tac, but it works well and doesn't mar the sights (I did not put tape on the part that actually contacts the sight itself, but did use a couple of layers on the clamp portion and shimmed it with a bit of cardboard under the slide for my FNP 9)

There's enough clearance for the suppressor sights?

 

[djv38]

There's enough clearance for the suppressor sights?

Just checked, unfortunately no, it just goes over the base of the front sight (like scrapes the top of the base of the front sight). For the rear sight it's fine.

 

[TactiTex]

I was afraid of that.

 

[TactiTex]

For future reference: They now sell an XL version for suppressor sights.
Fisher Solutions - New! XL Tool - El Cajon, CA

 

[djv38]

For future reference: They now sell an XL version for suppressor sights.
Fisher Solutions - New! XL Tool - El Cajon, CA

I emailed them earlier today and they said it is 0.200" taller than the standard blade.

 

[TactiTex]

I emailed them earlier today and they said it is 0.200" taller than the standard blade.

Talked to them yesterday and the guy said it would definitely work. It's on it's way.
I'll let y'all know how it goes when I get it.

 

[marshal kane]

I have one of these: Fisher Solutions - Home - El Cajon, CA . . .

I just ordered the standard model $59.95, no tax and free shipping.

 

[TactiTex]

I just ordered the standard model $59.95, no tax and free shipping.

So you dont have suppressor sights?

 

[TactiTex]

I just ordered the standard model $59.95, no tax and free shipping.

I gotta ask,did you read the whole thread? It appears the standard model wont work for the front sights if you have suppressor sights.
I'd hate to see you have to send your purchase back.

 

[marshal kane]

Thanks for your concern. I'm actually ordering this for a Kahr P9 and a Smith & Wesson model 41. Looks like a nice affordable tool.

 

[djv38]

Thanks for your concern. I'm actually ordering this for a Kahr P9 and a Smith & Wesson model 41. Looks like a nice affordable tool.

It works well, just have to shim a bit (I used cardboard and tape). Kind of wish the XL was available when I ordered mine, but oh well. Might be able to have a buddy machine a taller blade.